Free chainsaw pre-start checklist
Free chainsaw pre-start checklist (PDF-ready). Covers chain tension, bar, chain brake, throttle lock, spark arrestor and PPE. Download free.
Updated 3 May 2026
Chainsaw Pre-Start Checklist
Daily pre-start safety inspection for chainsaws
Chain and Bar
Chain Brake
Throttle and Controls
Spark Arrestor
Anti-Vibration Mounts
Fuel and Oil System
PPE Check
Operator
Signature
Print name
Date & time
Supervisor Acknowledgement
Signature
Print name
Date
How to use: download the PDF, print or complete digitally on any device.
- PDF format, ready to print or fill on screen
- Use as-is or customise to suit your operation
- Go digital in MapTrack for photos, alerts and audit trails
Two ways to use it
Use in MapTrack →Use it digitally instead
Unlimited usersThese same 22 checks, already built.
- Scan the asset’s QR tag with any phone
- Submitted forms can trigger alerts
- Photos on fails, audit-ready records
- Export responses, PDF reports with your logo
Free trial. No credit card needed.
Trusted by teams across Australia and New Zealand
We respect your privacy. Unsubscribe anytime.
These templates are free general guides provided as-is. They do not constitute legal, safety or compliance advice. You are responsible for ensuring any form meets your specific workplace obligations, industry standards and applicable regulations.
Don't just download it - use it live. Start a free workspace with this chainsaw pre-start checklist already built, so your crew can run it from a phone.
Commercial Director
Key takeaways
- The MapTrack chainsaw pre-start checklist contains 22 checks across 7 sections. Sections covered: Chain and Bar, Chain Brake, Throttle and Controls, Spark Arrestor, Anti-Vibration Mounts, Fuel and Oil System, PPE Check.
Enter your email below to download this chainsaw pre-start checklist as a ready-to-use PDF.
Used by construction, mining and field service teams
What is a chainsaw pre-start checklist?
A chainsaw pre-start checklist is a structured daily inspection form completed before operating a chainsaw on any worksite. It is used by arborists, forestry workers, landscapers, council crews, emergency services and general operators to confirm a chainsaw is safe to use before each cutting session. The checklist covers chain tension and sharpness, guide bar condition and wear, chain brake operation, throttle lock and trigger interlock, anti-vibration mounts, muffler and spark arrestor condition, chain catcher, fuel and bar oil levels, air filter and starter cord, and all required personal protective equipment including chainsaw chaps or trousers, helmet with visor and hearing protection, steel-capped boots and gloves.
In Australia, the WHS Act and WHS Regulations require a PCBU to ensure plant, including chainsaws, is inspected before use and maintained in a safe condition. Chainsaws are classified as high-risk plant due to the cutting chain, kickback hazard, and vibration exposure. Australian Standard AS/NZS 2727 provides guidance on chain saw safety. A documented pre-start checklist is the standard method for meeting these obligations and provides evidence for audits, incident investigations and insurer requirements.
Learn more about pre-start inspections in MapTrack.
Benefits of using this chainsaw pre-start checklist
- Kickback prevention: verify the chain brake engages correctly and the chain catcher is in place before every use.
- Chain integrity: confirm chain tension, sharpness and condition to reduce the risk of chain derailment or breakage.
- Fire safety: check the spark arrestor and muffler condition to prevent ignition in dry or fire-prone environments.
- Operator safety: ensure all required PPE (chaps, helmet, visor, hearing protection, gloves, boots) is present and in serviceable condition.
- WHS compliance: documented pre-start inspections demonstrate the PCBU has met their duty of care for plant inspections under WHS Regulations.
- Vibration management: inspect anti-vibration mounts and handles to reduce hand-arm vibration exposure for operators.
Benefits of digitising forms in MapTrack
When you digitise chainsaw checklists in MapTrack, you get:
- Field users can easily scan a QR code to complete a form on mobile. Unlimited users.
- Automatically get alerts when faults are identified.
- Link every form digitally as a PDF to the relevant asset, location or person.
- Receive a digital PDF copy with every submission to your email.
- Ability to share forms digitally.
- Build conditional logic (show or hide questions based on answers).
- Take pictures or attach photos. Not possible with a paper-based form.
- Electronic signatures.
- Edit forms later without reprinting.
- Restrict permissions (who can view, complete or approve).
- Build forms with AI (describe what you need and MapTrack suggests the form).
- Auto-schedule pre-start forms so operators are prompted before every shift.
- Flag overdue pre-starts on the dashboard so nothing leaves the yard unchecked.
- Link each pre-start to the asset record for a complete inspection history.
Book a demo to see how MapTrack handles chainsaw checklists.
Try MapTrack free for 30 days
Full access to every feature. No credit card required. Per-asset pricing so you scale as your fleet grows.
- No credit card required
- 30 days free trial
- Cancel anytime
1-2 days/week saved
“Bloody amazing! We used to spend 1-2 days a week tracking and managing our generators alone.”
Steve McAllister
Asset Coordinator, Saunders International
What to include in a chainsaw pre-start checklist
This chainsaw pre-start checklist covers 10 key areas:
- Chainsaw details: make, model, serial/fleet number, bar length, chain type and site location.
- Operator details: name, qualification/competency reference, inspection date and time.
- Chain and bar: chain tension, chain sharpness, depth gauges, guide bar condition, bar groove wear, bar nose sprocket.
- Chain brake and safety: chain brake operation (manual and inertia), throttle lock, trigger interlock, chain catcher.
- Anti-vibration system: front and rear anti-vibration mounts, handle condition.
- Engine and fuel: fuel level, bar and chain oil level, air filter, spark plug, starter cord, choke and decompression valve.
- Muffler and spark arrestor: muffler condition, spark arrestor screen (clean and intact).
- PPE check: chainsaw chaps or trousers, helmet with face visor, hearing protection, chainsaw gloves, steel-capped boots.
- Defect register: item, description, action required, reported to.
- Sign-off: operator signature and date.
How to use this chainsaw pre-start checklist
- Record chainsaw and operator details: Note the chainsaw make, model, serial number and bar length at the top of the form. Record your name, competency details (such as AHCPCM205), the date, time and site location for traceability.
- Inspect chain bar and safety devices: Check chain tension by pulling the chain at the bar midpoint and verify sharpness of each cutter tooth. Inspect the guide bar for groove wear and nose sprocket condition. Test the chain brake using both manual push and inertia activation methods.
- Check engine fuel and spark arrestor: Verify fuel and bar oil levels are adequate for the planned cutting session. Inspect the air filter for blockage, check the starter cord for fraying, examine the muffler and confirm the spark arrestor screen is clean and undamaged.
- Inspect anti-vibration mounts and handles: Check front and rear anti-vibration mounts for cracks, perishing or deterioration that would increase vibration transmission. Confirm both handles are secure, undamaged and provide a firm grip. Replace any worn mounts before operation.
- Verify PPE is complete and serviceable: Confirm you have chainsaw chaps or trousers meeting AS/NZS 4453.3, a helmet with face visor, hearing protection rated for chainsaw noise, chainsaw gloves with cut protection and steel-capped boots, all in serviceable condition.
- Record defects and sign off: Log any faults in the defect register with a clear description and action required. Report safety-critical defects to the supervisor before using the chainsaw. Sign, print your name and date the completed checklist.
In MapTrack, you can run digital pre-starts attached to each asset. Each submission is stored as a timestamped PDF against the asset record.
Get the free templateEnter your email above to download the full chainsaw pre-start checklist as a PDF.Back to download formHow often should you complete this checklist?
A chainsaw pre-start inspection must be completed before each use or at the start of each cutting session. If the chainsaw is used by multiple operators each operator must complete their own pre-start check. Chainsaws used in arborist and forestry operations are typically inspected at the start of every shift. The chain brake must be tested before every cutting session without exception.
The WHS Regulations require the PCBU to ensure plant is inspected and maintained so it remains safe. Most state and territory codes of practice for tree work and chainsaw operation mandate a daily pre-start inspection. In MapTrack you can schedule chainsaw inspections by asset and receive alerts when checks are overdue ensuring no chainsaw is operated without a current pre-start record.
Frequently asked questions
Applicable regulatory standards
This template aligns with the following regulations and standards:
- WHS Regulations 2017 (Part 5.1 Plant)
- AS/NZS 2727 (Chain saw safety)
- PCBU duty of care (WHS Act 2011, Section 19)
Chainsaw Pre-Start Checklist preview
The numbers behind this chainsaw pre-start checklist
Every figure below is sourced and dated, so you can quote it in a toolbox talk, a budget case or a board paper without having to chase the original report.
Embed this free template on your website
Run an industry blog, trade association site, or training resource? Drop a preview of this free chainsaw pre-start checklist straight into your page. The snippet is self-contained, needs no scripts, and links readers back to the full free template.
<div style="max-width:480px;font-family:system-ui,-apple-system,'Segoe UI',Roboto,sans-serif;border:1px solid #E5E7EB;border-radius:12px;padding:20px;background:#ffffff;">
<p style="font-size:12px;font-weight:700;letter-spacing:0.05em;text-transform:uppercase;color:#071D49;margin:0;">Free template</p>
<p style="font-size:18px;font-weight:700;color:#071D49;margin:6px 0 0;">Chainsaw Pre-Start Checklist</p>
<ul style="margin:12px 0 0;padding-left:18px;color:#374151;font-size:14px;line-height:1.6;">
<li style="margin:4px 0;">Chainsaw details: make, model, serial/fleet number, bar length, chain type and site location.</li>
<li style="margin:4px 0;">Operator details: name, qualification/competency reference, inspection date and time.</li>
<li style="margin:4px 0;">Chain and bar: chain tension, chain sharpness, depth gauges, guide bar condition, bar groove wear, bar nose sprocket.</li>
<li style="margin:4px 0;">Chain brake and safety: chain brake operation (manual and inertia), throttle lock, trigger interlock, chain catcher.</li>
<li style="margin:4px 0;">Anti-vibration system: front and rear anti-vibration mounts, handle condition.</li>
<li style="margin:4px 0;">Engine and fuel: fuel level, bar and chain oil level, air filter, spark plug, starter cord, choke and decompression valve.</li>
</ul>
<p style="font-size:13px;color:#6B7280;margin:14px 0 0;padding-top:12px;border-top:1px solid #E5E7EB;">Free <a href="https://www.maptrack.com/templates/chainsaw-pre-start-checklist" style="color:#071D49;font-weight:600;text-decoration:none;">Chainsaw Pre-Start Checklist</a> by MapTrack</p>
</div>Free to reuse, including commercially. This template is published under a Creative Commons Attribution 4.0 licence. Copy it, adapt it, put it on your own site or in your own docs. All we ask is that you credit MapTrack with a link back to this page. The snippet above already includes that credit, so if you use it as-is you’re covered.
Cite this template
Writing about this topic? You’re welcome to quote this checklist. Here’s the wording to use so your readers can find the original.
The MapTrack chainsaw pre-start checklist contains 22 checks across 7 sections.
- Short attribution
- MapTrack Chainsaw Pre-Start Checklist, https://www.maptrack.com/templates/chainsaw-pre-start-checklist
- Reference list
- MapTrack. (2026). Chainsaw Pre-Start Checklist [Checklist template]. Retrieved from https://www.maptrack.com/templates/chainsaw-pre-start-checklist
Free to reuse with credit under a Creative Commons Attribution 4.0 licence. If you’d rather link straight to it, the page is https://www.maptrack.com/templates/chainsaw-pre-start-checklist.
Need to run digital pre-starts attached to each asset?
Register every chainsaw in MapTrack, attach digital forms, and get a complete history of every inspection, service and compliance record.
Pre-start inspections · All templates · Pricing · Book a demo