Free forklift monthly inspection checklist
Free forklift monthly inspection checklist. Mast chain 3% stretch, fork blade thickness, seat switch, brake on grade, defect log. AS 2359 aligned.
Updated 25 May 2026
Forklift Monthly Inspection
Monthly periodic inspection | Per AS 2359
Overhead guard, backrest & carriage
Mast, chains & forks
Hydraulic system
Tyres, wheels & drive axle
Brakes & steering
Operator station & safety devices
Function tests under load
Documentation & close-out
How to use: download the PDF, print or complete digitally on any device.
- PDF format, ready to print or fill on screen
- Use as-is or customise to suit your operation
- Go digital in MapTrack for photos, alerts and audit trails
Two ways to use it
Use in MapTrack →Use it digitally instead
Unlimited usersThese same 39 checks, already built.
- Scan the asset’s QR tag with any phone
- Submitted forms can trigger alerts
- Photos on fails, audit-ready records
- Export responses, PDF reports with your logo
Free trial. No credit card needed.
Trusted by teams across Australia and New Zealand
We respect your privacy. Unsubscribe anytime.
These templates are free general guides provided as-is. They do not constitute legal, safety or compliance advice. You are responsible for ensuring any form meets your specific workplace obligations, industry standards and applicable regulations.
Don't just download it - use it live. Start a free workspace with this forklift monthly inspection checklist already built, so your crew can run it from a phone.
Commercial Director
Key takeaways
- The MapTrack forklift monthly inspection checklist contains 39 checks across 8 sections. Sections covered: Overhead guard, backrest & carriage, Mast, chains & forks, Hydraulic system, Tyres, wheels & drive axle, Brakes & steering, Operator station & safety devices, Function tests under load, Documentation & close-out.
Enter your email below to download this forklift monthly inspection checklist as a ready-to-use PDF.
Used by construction, mining and field service teams
What is a forklift monthly inspection checklist?
A forklift monthly inspection is a structured form used by a competent person to verify the structural, hydraulic, drivetrain, and operator-protective systems of a counterbalance forklift at a depth that daily pre-start checks cannot reach. Where the pre-start covers visible fluid levels, horn, lights, and basic function, the monthly takes the truck out of service for two to three hours and measures wear against OEM tolerances: mast chain stretch against the AS 2359 three percent limit, fork blade thickness against the OEM ninety percent rule, fork heel wear, carriage hooks for positive lock, backrest and overhead guard weld integrity, and lift and tilt cylinder seal weep. It also confirms safety interlocks such as the operator-presence seat switch and parking brake hold on a graded surface.
Forklift monthly inspections sit at the intersection of plant compliance and reliability engineering. The competent person signs the checklist and the record becomes admissible evidence under WHS Regulations 2011 Chapter 5 that the duty holder has inspected and maintained the truck. The same record drives the maintenance plan: a mast chain measured at 2.7 percent stretch this month will breach the three percent limit before the next inspection, so the planner orders the chain pair now rather than chasing a breakdown later. LPG, diesel, and electric counterbalance forklifts share most of the inspection scope, with battery condition and connector wear added for electric trucks and fuel system, cooling, and exhaust checks added for internal combustion units.
Learn more about maintenance and work orders in MapTrack.
Benefits of using this forklift monthly inspection checklist
- Wear measurement against OEM: Catches mast chain stretch, fork thickness loss, and cylinder seal weep before they breach AS 2359 limits or cause a load drop.
- Structural assurance: Confirms overhead guard, backrest, carriage hooks, and chassis welds remain intact after a month of impacts, racking strikes, and load cycling.
- Safety interlock verification: Tests seat switch, parking brake hold on grade, hydraulic lockout, and travel cutout that pre-starts do not exercise under load.
- Defect log closure: Forces a monthly review of operator-reported faults so recurring issues surface and unresolved tickets do not accumulate across shifts.
- Service interval trigger: Surfaces wear trends that justify ordering parts ahead of the 250, 500, or 1000 hour service, reducing breakdown downtime.
- Compliance evidence: Generates an auditable record signed by a competent person that satisfies WHS Regulations 2011 Chapter 5 plant inspection duties.
- Warehouse uptime: Taking the truck out for a controlled monthly check catches mast, brake and interlock wear before it strands a forklift in the racking aisle and stalls pick, putaway and despatch flow.
Benefits of digitising forms in MapTrack
When you digitise forklift checklists in MapTrack, you get:
- Field users can easily scan a QR code to complete a form on mobile. Unlimited users.
- Automatically get alerts when faults are identified.
- Link every form digitally as a PDF to the relevant asset, location or person.
- Receive a digital PDF copy with every submission to your email.
- Ability to share forms digitally.
- Build conditional logic (show or hide questions based on answers).
- Take pictures or attach photos. Not possible with a paper-based form.
- Electronic signatures.
- Edit forms later without reprinting.
- Restrict permissions (who can view, complete or approve).
- Build forms with AI (describe what you need and MapTrack suggests the form).
- Trigger work orders automatically when a fault is logged during an inspection.
- Track service intervals by hours, kilometres or calendar date in one place.
- Attach supplier invoices and parts receipts to each maintenance record.
Book a demo to see how MapTrack handles forklift checklists.
Try MapTrack free for 30 days
Full access to every feature. No credit card required. Per-asset pricing so you scale as your fleet grows.
- No credit card required
- 30 days free trial
- Cancel anytime
1-2 days/week saved
“Bloody amazing! We used to spend 1-2 days a week tracking and managing our generators alone.”
Steve McAllister
Asset Coordinator, Saunders International
What to include in a forklift monthly inspection checklist
This forklift monthly inspection checklist covers 11 key areas:
- Mast chain stretch measurement across a fixed gauge length compared to OEM 3% maximum (AS 2359)
- Lift cylinder and tilt cylinder seal weep walk with the mast cycled through full range
- Fork blade thickness at the heel measured against OEM new dimension and 90% wear limit
- Fork heel wear, fork tip damage, and positive engagement of fork retention pins
- Carriage hooks, fork locator pins, and load backrest extension weld integrity
- Overhead guard structural inspection: welds, mounting bolts, FOPS sticker legibility, and impact damage
- Operator-presence seat switch, parking brake hold on a graded surface, and travel interlock function
- Hydraulic hose chafing walk along mast, chassis, and tilt cylinder routing
- Battery state-of-health, connector condition, and electrolyte level (electric) or fuel system, cooling, and exhaust (IC)
- Tyre tread depth, sidewall damage, wheel nut torque, and steer axle play
- Defect log review: closing out the prior month of operator-reported faults and verifying repairs
How to use this forklift monthly inspection checklist
- Take the truck out of service and review history: Lock out, tag out, and pull the last month of pre-start sheets, defect log entries, and any work orders. Note recurring complaints such as drift, slow lift, or steering wander so the inspection focuses on those systems rather than treating every fault as new.
- Measure mast chain stretch against the AS 2359 3% limit: Park on level ground, fully lower the mast, and measure a fixed gauge length across the chain (typically 12 to 20 pitches). Compare against the OEM new dimension and flag any chain exceeding 2.5% stretch for replacement at the next service before the 3% limit is breached.
- Walk the lift and tilt cylinders for seal weep: Cycle the mast through full lift, lower, and tilt range with the truck unloaded and again under rated load. Inspect rod surfaces, gland seals, and hose unions for oil weep, paying attention to fresh oil tracks that indicate active leakage rather than residue.
- Measure fork blade thickness and inspect the heel: At the heel of each fork, measure blade thickness with a calliper and compare to the OEM new dimension. Replace any fork below the 90% wear limit (typically 10% reduction). Inspect for cracks at the heel weld, bent tips, and twisted blades.
- Inspect carriage, backrest, and overhead guard for structural integrity: Check carriage hooks for positive lock function, fork locator pins for engagement, load backrest welds, overhead guard mounting bolt torque, and FOPS sticker legibility. Document any cracked welds, bent members, or impact damage with photos.
- Verify operator-protective interlocks under load: Sit on the seat with the parking brake set, attempt to drive without the seat occupied (travel must inhibit), and park the loaded truck on the steepest available grade to confirm the parking brake holds without creep. Test hydraulic lockout when the operator leaves the seat.
- Walk hydraulic hoses, electrical looms, and the chassis frame: Trace every hose from cylinder to manifold, looking for chafing against mast channels, sharp edges, or cable looms. Flex hoses at unions to detect outer-jacket cracking. Inspect chassis welds, counterweight mounting, and tow point.
- Inspect drivetrain, tyres, and brakes: Check tyre tread depth, sidewall cuts, and wheel nut torque to OEM spec. For electric trucks, inspect battery connector wear, cell voltages, and electrolyte. For IC trucks, check coolant, oil, fuel system unions, and exhaust integrity. Test service brake travel and confirm parking brake holds on grade.
- Close out the defect log and sign the certificate: Verify each open defect from the prior month is either repaired or carried forward with a target close date. Sign the inspection certificate, file the record, and tag the truck as serviceable or out-of-service. Update the asset record with the next inspection due date.
In MapTrack, you can schedule and track maintenance digitally. Each submission is stored as a timestamped PDF against the asset record.
Get the free templateEnter your email above to download the full forklift monthly inspection checklist as a PDF.Back to download formHow often should you complete this checklist?
Monthly is the standard cadence for a competent-person structural and safety inspection on a counterbalance forklift in regular service, and it is the interval most OEM manuals and Australian fleet operators follow alongside the AS 2359 plant inspection regime. The daily pre-start covers fluids, lights, horn, and basic function and stays with the operator; the monthly is a deeper two to three hour inspection by a maintenance technician or licensed forklift mechanic that takes the truck out of service. Escalate to fortnightly or weekly if the truck operates more than 200 hours per month, runs in cold-store or food-grade environments, handles abrasive or corrosive loads, or has a history of unresolved defects. Escalate immediately and out-of-cycle after any racking strike, dropped load, mast chain replacement, hydraulic component change, or operator-reported brake or steering anomaly. Quieter trucks on light single-shift duty may extend to six-weekly with documented justification.
Frequently asked questions
Applicable regulatory standards
This template aligns with the following regulations and standards:
- AS 2359 Powered Industrial Trucks
- AS 4024.3611 Industrial Trucks Safety
- WHS Regulations 2011 Chapter 5 Plant Safety
- Safe Work Australia Code of Practice Managing Risks of Plant in the Workplace
Forklift Monthly Inspection Checklist preview
The numbers behind this forklift monthly inspection checklist
Every figure below is sourced and dated, so you can quote it in a toolbox talk, a budget case or a board paper without having to chase the original report.
Embed this free template on your website
Run an industry blog, trade association site, or training resource? Drop a preview of this free forklift monthly inspection checklist straight into your page. The snippet is self-contained, needs no scripts, and links readers back to the full free template.
<div style="max-width:480px;font-family:system-ui,-apple-system,'Segoe UI',Roboto,sans-serif;border:1px solid #E5E7EB;border-radius:12px;padding:20px;background:#ffffff;">
<p style="font-size:12px;font-weight:700;letter-spacing:0.05em;text-transform:uppercase;color:#071D49;margin:0;">Free template</p>
<p style="font-size:18px;font-weight:700;color:#071D49;margin:6px 0 0;">Forklift Monthly Inspection Checklist</p>
<ul style="margin:12px 0 0;padding-left:18px;color:#374151;font-size:14px;line-height:1.6;">
<li style="margin:4px 0;">Mast chain stretch measurement across a fixed gauge length compared to OEM 3% maximum (AS 2359)</li>
<li style="margin:4px 0;">Lift cylinder and tilt cylinder seal weep walk with the mast cycled through full range</li>
<li style="margin:4px 0;">Fork blade thickness at the heel measured against OEM new dimension and 90% wear limit</li>
<li style="margin:4px 0;">Fork heel wear, fork tip damage, and positive engagement of fork retention pins</li>
<li style="margin:4px 0;">Carriage hooks, fork locator pins, and load backrest extension weld integrity</li>
<li style="margin:4px 0;">Overhead guard structural inspection: welds, mounting bolts, FOPS sticker legibility, and impact damage</li>
</ul>
<p style="font-size:13px;color:#6B7280;margin:14px 0 0;padding-top:12px;border-top:1px solid #E5E7EB;">Free <a href="https://www.maptrack.com/templates/forklift-monthly-inspection-checklist" style="color:#071D49;font-weight:600;text-decoration:none;">Forklift Monthly Inspection Checklist</a> by MapTrack</p>
</div>Free to reuse, including commercially. This template is published under a Creative Commons Attribution 4.0 licence. Copy it, adapt it, put it on your own site or in your own docs. All we ask is that you credit MapTrack with a link back to this page. The snippet above already includes that credit, so if you use it as-is you’re covered.
Cite this template
Writing about this topic? You’re welcome to quote this checklist. Here’s the wording to use so your readers can find the original.
The MapTrack forklift monthly inspection checklist contains 39 checks across 8 sections.
- Short attribution
- MapTrack Forklift Monthly Inspection Checklist, https://www.maptrack.com/templates/forklift-monthly-inspection-checklist
- Reference list
- MapTrack. (2026). Forklift Monthly Inspection Checklist [Checklist template]. Retrieved from https://www.maptrack.com/templates/forklift-monthly-inspection-checklist
Free to reuse with credit under a Creative Commons Attribution 4.0 licence. If you’d rather link straight to it, the page is https://www.maptrack.com/templates/forklift-monthly-inspection-checklist.
Need to schedule and track maintenance digitally?
Register every forklift in MapTrack, attach digital forms, and get a complete history of every inspection, service and compliance record.
Maintenance and work orders · All templates · Pricing · Book a demo